Cisco
Jr. Member
 Offline
Location: LI NY USA
Posts: 34
|
 |
« on: September 04, 2009, 04:26:17 PM » |
|
I was asked by a member from another forum if these pen-style lasers could be modded, being up for the challenge I ordered a few. So the answer is Yes, they can be modded. They take 2 10440's so I had to cut the shell down and re-install the insides to allow for 1 10440. I cut the top section off (where the pocket clip is crimped on to the shell)and drilled a new hole for the switch button this way I could keep the threaded end cap. You can get these off e-bay for $2.99 each shipped from USA or from numerous China suppliers for about the same price. The black one had a scratch on it so I modded a Blue one ( UK BLUE...  ) New Powerful Red Laser Pointer Pen Beam Light 5mW - eBay (item 230372923452 end time Sep-29-09 21:56:19 PDT) Cheers Cisco...     |
|
|
|
|
Logged
|
|
|
|
|
Crossbow
|
|
« Reply #1 on: September 04, 2009, 04:44:11 PM » |
|
Thats absolutely phenomenal  |
|
|
|
|
Logged
|
Optimism is the triumph of hope over experience
|
|
|
minus1724
Full Member
Offline
Location: Silkeborg / Denmark
Posts: 167
|
|
« Reply #2 on: September 04, 2009, 05:33:24 PM » |
|
nice job.. just ordered one |
|
|
|
|
Logged
|
|
|
|
igetcha
Full Member
Offline
Location: Romford, UK
Posts: 205
|
|
« Reply #3 on: September 05, 2009, 08:04:38 AM » |
|
nice one mate! how does it vape.......any good?
|
|
|
|
|
Logged
|
|
|
|
|
Nick OTeen
|
|
« Reply #4 on: September 05, 2009, 12:37:13 PM » |
|
Very nice!
|
|
|
|
|
Logged
|
|
|
|
Cisco
Jr. Member
Offline
Location: LI NY USA
Posts: 34
|
|
« Reply #5 on: September 06, 2009, 12:20:44 AM » |
|
Hey Guys, Did a little mass production today and modded 5 more of these pen style laser pointers all with different attys and 1 with 2x10440's I didn't like look of the atty connector pressed into the chrome trim ring so I recessed the atty connectors into the shell and drilled out the trim rings so the atty goes inside the ring not sitting on top of it, gives a nice recessed look and makes them a tad shorter also... I also made a 901 with 2x10440's for higher voltage vaping.Both batteries are 3.6 volt x 2 ( my meter read 8.3v fully charged) so using ohms law and some math I installed a 1ohm 2watt resistor in the tube. It softens the blow from 2x3.6v batteries and knocks the amp draw down to 1.8 amps (Single 3.7v battery draws 1.2 amps) I didn't check the amps under load but its probably in the 1.4 to 1.6 range, maybe the sweet spot... Cheers Cisco....    |
|
|
|
|
Logged
|
|
|
|
|
Crossbow
|
|
« Reply #6 on: September 06, 2009, 12:58:22 AM » |
|
I'm not saying I love this design, or anything...but how much for one?  |
|
|
|
|
Logged
|
Optimism is the triumph of hope over experience
|
|
|
Cisco
Jr. Member
Offline
Location: LI NY USA
Posts: 34
|
|
« Reply #7 on: September 06, 2009, 01:58:37 AM » |
|
nice one mate! how does it vape.......any good?
It vapes just as good as any other single battery mod. It doesnt have near the vape time between chargers as the larger battery mods. But it will double or triple a reg e-cig battery and it is small and it has style.... I would have no problem using this in any public venue Cisco... |
|
|
|
|
Logged
|
|
|
|
Cisco
Jr. Member
Offline
Location: LI NY USA
Posts: 34
|
|
« Reply #8 on: September 06, 2009, 02:05:13 AM » |
|
I'm not saying I love this design, or anything...but how much for one? I am not saying I am going to sell them, but if I did maybe $40 USD If that sounds pricey you can mod one yourself for about $6 USD Laser pointer and connector are about the only parts you will need to do this mod Cisco... |
|
|
|
|
Logged
|
|
|
|
|
damulta
|
|
« Reply #9 on: September 06, 2009, 03:36:03 AM » |
|
Very slick looking!
I think 40USD is a very fair price, and to the fact that your paying someone to make it for you makes it fair. People pay the people at Computer shops 50 dollars an hour. That may be easy work for the person making the cash, but your paying that person for their knowledge about what they are doing along with the work.
|
|
|
|
|
Logged
|
|
|
|
|
kitsune(Lisa)
|
|
« Reply #10 on: September 06, 2009, 02:27:25 PM » |
|
I agree Damulta--it's the knowlege and skill. I couldn't mod my way out of abox most days. There are tons of things we use each day that we could make ourselves for cheap, but we don't. They really are sharp looking.
|
|
|
|
|
Logged
|
|
|
|
minus1724
Full Member
Offline
Location: Silkeborg / Denmark
Posts: 167
|
|
« Reply #11 on: September 14, 2009, 05:58:30 PM » |
|
just want to say thanks again for the great idea, I have just made one in black, and have an idea for a indicator light in blue, will post some pic when done.
|
|
|
|
|
Logged
|
|
|
|
|
kitsune(Lisa)
|
|
« Reply #12 on: September 15, 2009, 04:29:56 AM » |
|
Nice minus--looking forward to pictures Lisa  |
|
|
|
|
Logged
|
|
|
|
minus1724
Full Member
Offline
Location: Silkeborg / Denmark
Posts: 167
|
|
« Reply #13 on: September 19, 2009, 01:48:58 PM » |
|
nice one mate! how does it vape.......any good?
It vapes just as good as any other single battery mod. It doesnt have near the vape time between chargers as the larger battery mods. But it will double or triple a reg e-cig battery and it is small and it has style.... I would have no problem using this in any public venue Cisco... Hi.. just want to hear if you have had any problems with the push button. My button just kind of collapsed, and stopped working. I´m thinking that the button cant handle the amp draw. |
|
|
|
|
Logged
|
|
|
|
minus1724
Full Member
Offline
Location: Silkeborg / Denmark
Posts: 167
|
|
« Reply #14 on: September 23, 2009, 12:06:38 PM » |
|
Hey Guys, Did a little mass production today and modded 5 more of these pen style laser pointers all with different attys and 1 with 2x10440's I didn't like look of the atty connector pressed into the chrome trim ring so I recessed the atty connectors into the shell and drilled out the trim rings so the atty goes inside the ring not sitting on top of it, gives a nice recessed look and makes them a tad shorter also... I also made a 901 with 2x10440's for higher voltage vaping.Both batteries are 3.6 volt x 2 ( my meter read 8.3v fully charged) so using ohms law and some math I installed a 1ohm 2watt resistor in the tube. It softens the blow from 2x3.6v batteries and knocks the amp draw down to 1.8 amps (Single 3.7v battery draws 1.2 amps) I didn't check the amps under load but its probably in the 1.4 to 1.6 range, maybe the sweet spot... Cheers Cisco.... HI.. were did you get the 1ohm 2watt resistor from, I cant find it any where  |
|
|
|
|
Logged
|
|
|
|
|
|
minus1724
Full Member
Offline
Location: Silkeborg / Denmark
Posts: 167
|
|
« Reply #16 on: September 27, 2009, 09:02:32 PM » |
|
yes google is my friend , but I was looking in EU not the US. no a fens  it´s a lot faster for shipping. and I did find a Danish Electronic-pusher, and got my parts.  |
|
|
|
|
Logged
|
|
|
|
shahnowaz
Newbie
Offline
Posts: 1
|
|
« Reply #17 on: October 15, 2009, 04:25:59 AM » |
|
where i am gonna get the connector newbie in here |
|
|
|
|
Logged
|
|
|
|
minus1724
Full Member
Offline
Location: Silkeborg / Denmark
Posts: 167
|
|
« Reply #18 on: October 15, 2009, 07:14:14 AM » |
|
where i am gonna get the connector newbie in here From a dead battery |
|
|
|
|
Logged
|
|
|
|
E.T.
Newbie
Offline
Posts: 10
|
|
« Reply #19 on: July 26, 2011, 02:10:32 PM » |
|
Excellent job...I've been lurking the mod forum for several months. I particularly like this as I have several of these lazer pens laying about.
|
|
|
|
|
Logged
|
|
|
|
RichJr
Global Moderator
Elite Hero Member
Offline
Location: Boston MA. USA
Posts: 6160
I can't see!
|
|
« Reply #20 on: July 26, 2011, 03:14:05 PM » |
|
Hi et. Welcome to the forum. I've been here for a while and I've never seen this until you posted! I have one o those pens lasers sittin in front of me hmmmm.
|
|
|
|
|
Logged
|
Rich (tech guru)  I do everything with my iPhone. Meep Meep |
|
|
E.T.
Newbie
Offline
Posts: 10
|
|
« Reply #21 on: July 26, 2011, 03:18:19 PM » |
|
Thanks rtsjr.....I do everything with my DROID.. |
|
|
|
|
Logged
|
|
|
|
RichJr
Global Moderator
Elite Hero Member
Offline
Location: Boston MA. USA
Posts: 6160
I can't see!
|
|
« Reply #22 on: July 26, 2011, 03:38:33 PM » |
|
Hehehe we just love being mobile huh. Why carry a desktop when you could just pull out your phone. I just ordered another laser from eBay $1.99 so I won't feel bad about ripping this one apart. Fun time. |
|
|
|
|
Logged
|
Rich (tech guru) I do everything with my iPhone. Meep Meep |
|
|
B.A.M.F
Jr. Member
Offline
Posts: 30
|
|
« Reply #23 on: March 12, 2012, 03:16:06 PM » |
|
thats petty sweet.
|
|
|
|
|
Logged
|
|
|
|
|
